Why the Shower Gets Hot or Cold When You Flush (and How To Prevent It)

A sudden burst of piping hot (or freezing cold) water is a showering human's worst nightmare. But what's the cause? And how can you prevent it? The DIY experts at Stack Exchange provide a few tips.

When the shower is running and someone flushes a toilet, why does the shower get cold (or sometimes hot) in some houses, but not others? More importantly, would fixing that require replacing the water heater, or re-doing the piping in the entire house? Or is there some cheap/easy way to fix it?

See the original question.

Tester101 answers:

Why You Get Burned

One of the most common plumbing configurations is a trunk and branch system. This is where a larger diameter pipe runs from one end of the building to the other, and smaller diameter pipes branch off to supply rooms or individual fixtures. If any of the branches demand water (you flush the toilet), there is less water available to all the other branches. Since the toilet only uses cold water, there is less cold water available to your shower when the toilet is filling. This causes the water in the shower to be warmer, because there is less cold water mixing with the hot water. There are a few ways to reduce or eliminate this burning feeling. Probably the cheapest is to reduce the amount of water going to the toilet.

Reducing Toilet Water

You can reduce how quickly the toilet uses water by simply closing the supply valve slightly. This means the toilet will take longer to fill, but will reduce the temperature fluctuation in the shower. Adjusting the supply valve can also have negative side effects, such as increased fill times and noise. You can also reduce the overall amount of water the toilet needs by either buying a low flow toilet, or placing a brick, jug of water, or other object in the tank. However, this method will reduce the amount of water available for each flush, so you may encounter difficulty clearing solids from the bowl.

Smarter Mixing

Installing a new mixing valve in the shower can reduce or eliminate the temperature fluctuations. Thermostatic mixing valves automatically balance the amount of hot and cold water being mixed, which will prevent drastic fluctuations in shower temperature. If the cold water flow is reduced (due to a toilet flush), the valve automatically adjusts the amount of hot water being mixed. This keeps the shower temperature more consistent, even when other fixtures are using water.

Increasing Available Water

Increasing the amount of water available in the system can alleviate the problem, but will likely require a major change to the plumbing. If you have a trunk and branch system, increasing the trunk pipe diameter and/or the branch pipe diameter (if the branch feeds the entire room) will increase the amount of water available to the fixtures.

Distributing Water Evenly

A more drastic solution would be to install a manifold with home runs. This would likely require a major plumbing renovation, with almost all of the plumbing changed. In this type of system, there is a central load balancing manifold. Then for each fixture in the house, a dedicated pipe is run between the fixture and the manifold.

Supply and Demand

In the end, it's all about supply and demand. If the demand is greater than the supply, you end up with a burnt butt. The only way to avoid uncomfortable showers is to reduce demand or increase supply.

Matthew PK answers:

The shower temperature changes when you flush (or use water) because the pressure in that supply line has changed. This means less supply to the mixing valve in the same setting. Modern thermostatic mixing valves are designed to keep the total pressure constant. This means that a reduction in cold water pressure (from a flush) is detected and the mixing valve responds by reducing corresponding flow in the hot water. So, the solution to shifting shower temperatures is to install a thermostatic mixing valve.

Tester101 comments:

The shower would get cold if somebody used hot water for something (almost certainly not a toilet flush), instead of cold. It could be caused by an over-enthusiastic thermostatic mixing valve, which reduced the hot water flow too much. Using up all the water in the hot water tank would also lead to a cold shower. And yes, you do have to install a thermostatic mixing valve at each shower/tub. They are used to replace the plain old standard mixing valve.

bcworkz comments:

I believe Matthew is suggesting that upgrading your shower valves is the best solution. I agree. A different water heater will do nothing. Changing the piping so the pressure change is minimal will help but not eliminate the problem. A thermostatic mixing valve is the best solution, but note it still takes a brief time for it to adjust to a sudden change in pressure, so a brief cold period will still be noticed.

Find more answers or leave your own at the original post. See more questions like this at Home Improvement, the DIY site at Stack Exchange. And of course, feel free to ask a question yourself.

Image via Mark Sayer (Shutterstock).

Source: http://feeds.gawker.com/~r/lifehacker/full/~3/85bm626KrJM/why-the-shower-gets-hot-or-cold-when-you-flush-and-how-508252782

Met gala lauryn hill teacher appreciation week Jodi Arias trial cinco de mayo Mike Jeffries Abercrombie nascar